What makes a bunny pattern easy
A bunny is one of the friendlier animals for a first plush. The body can be a simple rounded shape, the limbs are short, and the long ears give the toy its character without any complicated shaping. An easy pattern usually has:
- A body made from two matching pieces, or a front and back with a gusset
- Short arms and legs, either sewn into the seams or attached afterward
- Two ears cut as simple elongated ovals
- A round tail, often a pompom or a small fabric circle
If you are new to reading patterns, our guide to stuffed animal sewing patterns explains markings and cutting terms.
Materials
- About 1/2 yard (roughly 45 cm) of fleece, minky or felt for the body, plus a small amount of contrasting fabric for the inner ears
- Polyester fiberfill
- Matching thread
- Embroidery thread or safety eyes for the face
- Pins or clips, scissors, a hand needle, and a turning tool such as a chopstick
Fleece and felt are forgiving because they do not fray. Minky feels soft but stretches and slides, so it takes patience; see sewing minky without stretching or shifting.
The pattern pieces
You can draft a basic bunny on paper with these shapes, or compare the list with a commercial pattern:
- Body: A pear or egg shape, wider at the bottom so the toy sits. Cut 2.
- Head: A rounded shape, or incorporate the head into the body outline for a one-piece design. Cut 2 if separate.
- Ears: Long ovals, about one third to one half of the body height. Cut 2 outer pieces and 2 inner pieces.
- Arms: Small tube or paddle shapes. Cut 4 for two arms.
- Feet: Oval pads or rounded shapes. Cut 2 or 4 depending on design.
- Tail: A circle, or a pompom.
A seam allowance of about 1/4 inch (6 mm) is common. Check your pattern instructions.
Step-by-step sewing
- Prepare the ears. Place each inner ear on an outer ear, right sides together, and sew around the curve, leaving the bottom open. Clip curves, turn right-side out and press lightly. Fold the base slightly and baste it so it sits upright or droops, depending on your style.
- Make the arms and feet. Sew each piece with right sides together, leave the top open, turn and stuff lightly.
- Add details to the face. It is easier to embroider the nose and eyes, or attach safety eyes, before sewing the front and back together. For toys intended for babies and toddlers, embroider the features instead of using plastic eyes or buttons.
- Assemble the body. Place the ears and limbs between the front and back body pieces with the raw edges lined up and the ear and limb bodies pointing inward. Pin them in place so they do not get caught in the seams.
- Sew around the body, leaving a gap of about 2 to 3 inches (5 to 8 cm) at the bottom or back for turning.
- Clip the curves by snipping small notches in the seam allowance, taking care not to cut the stitches. This helps the curves lie smooth after turning.
- Turn the bunny right-side out. Push the ears and limbs through the gap gently with a turning tool.
- Stuff. Start with small pieces of filling in the ears (or leave them unstuffed for a floppy look), then arms, legs and head, then fill the body. A firm fill helps the bunny sit.
- Close the gap with a ladder stitch. Work small stitches along each folded edge in turn, pulling the thread gently so the seam closes invisibly. If you need to fix a stitch later, see how to sew a hole in a soft toy.
- Attach the tail by hand stitching.
Ear and tail options
- Upright ears: Sew a narrow dart at the base, or stiffen with a layer of interfacing, so they stand.
- Floppy ears: Leave the ears unstuffed and sew them in at an angle. A similar design appears in the elephant plush with floppy ears.
- Tail: A fluffy pompom or a circle of fabric gathered around a small amount of filling.
Face details and safety
Embroidered eyes and a small stitched nose are a safe choice for very young children. For older children or display pieces, safety eyes can look neat, but they need to be installed according to the maker’s instructions and checked often. Avoid ribbons or loose trims on any toy for babies.
Troubleshooting
- The bunny flops over. Add more filling at the base, or sew a small round base into the bottom.
- The seams pucker. Clip curves more, and sew slowly around tight turns.
- Ears look uneven. Mark the ear position on each side with a pin before sewing, and measure from the center line.
- Stuffing looks lumpy. Use small pieces and push them into place rather than adding a single big clump.
Related
If you like this project, the owl plush sewing pattern for beginners and the penguin soft toy pattern use a similar rounded body. For a quicker version, try making a sock bunny with long ears.