Why minky is tricky
Minky is a soft polyester fabric with a short pile, and it’s a popular choice for soft toys because it feels so plush. It’s also stretchy, slippery and prone to shedding fibers. When you sew two layers together, the bottom layer tends to feed through the machine at a different rate than the top, so seams can shift, pucker or end up uneven.
The good news is that a few habits address most problems.
Before you cut
- Find the direction of greatest stretch. Most minky stretches more in one direction, usually across the width. Check by pulling gently both ways. Many patterns assume a particular stretch direction, so follow the pattern’s guidance.
- Check the pile direction. Stroke the fabric. It feels smooth in one direction and rougher in the other. Cut all pieces with the pile running the same way, usually downward on the finished toy. See our plush fabric guide for more on pile.
- Cut a single layer at a time. Layered cutting causes the pieces to shift. Trace the pattern on the back with a marker or chalk, and cut with sharp scissors, or use a rotary cutter and mat.
- Cut with the tips of the scissors, snipping the backing rather than the pile, to avoid chopping the fibers at the edge.
Supplies that help
- Clips instead of pins, which can leave holes or distort the pile. Pins work too, in the seam allowance.
- A walking foot (even-feed foot), which feeds both layers evenly. This is the single most useful accessory for minky. See best sewing machine features for making stuffed animals for more.
- A stretch or ballpoint needle and good-quality polyester thread.
- A seam ripper, because mistakes are common and minky hides unpicking marks.
- Interfacing or stabilizer for areas that must keep their shape.
Machine settings
- Use a longer stitch length than you would for cotton, often around 3 mm, and test on scraps.
- Reduce presser foot pressure if your machine allows it.
- Use a stretch-friendly stitch, such as a narrow zigzag or the stretch stitch on your machine, or a straight stitch with a longer length. Test on a scrap and pull the seam to check it doesn’t pop.
- Sew slowly.
Settings vary by machine, so a test seam on offcuts is worth the few minutes.
Sewing without shifting
- Put right sides together and align the edges.
- Clip every few centimeters, and more often on curves.
- Start sewing with the walking foot. Guide the fabric, but don’t pull or push it.
- Check the layers as you go. If the top layer is creeping forward, stop with the needle down, lift the foot and smooth the fabric.
- Push the pile inside the seam with a pin or the point of a seam ripper before you stitch, so it doesn’t get trapped on the right side.
- Backstitch at the start and end of each seam.
For a very slippery piece, hand-basting first, or using a thin strip of washable fabric glue tape in the seam allowance, can keep the layers together.
Stabilizing stretchy areas
Minky can sag around eyes, noses, joints and seams under strain. Fusible interfacing needs care: minky is sensitive to heat, so use low-heat settings and a pressing cloth, and test on a scrap, or choose sew-in or lightweight fusible options made for stretch fabrics. Another option is to sew a small piece of felt or woven fabric behind areas that will carry load.
Curves, corners and turning
- Clip curves and notch inside curves after sewing, being careful not to cut through the stitches. Our guide to sewing tiny curved plush pieces covers ears, paws and tails.
- Trim seam allowances to reduce bulk, especially at points like ears.
- Turn small parts with a chopstick or turning tool, and take care not to poke through the seam.
- After turning, use a pin to pick out any pile that’s trapped in the seam, and brush the seam.
Stuffing minky toys
Minky stretches under pressure, so overstuffing can distort the shape and make seams show. Fill in small pieces, shape as you go, and stop when the toy holds its form without the fabric straining. For types and quantities, see choosing stuffing for stuffed animals and how much stuffing a stuffed animal needs.
Cleaning up shedding
Cut minky sheds lint. Cut near a vacuum or a wastebasket, shake the pieces before sewing, and use a lint roller on the finished toy. Change the machine’s needle plate lint regularly.
Troubleshooting
- Seams wavy or stretched: use a walking foot, a longer stitch, and less tension on the fabric.
- Seams popping when stuffed: use a stretch stitch or sew a second line of stitching within the seam allowance.
- One layer longer than the other: more clips, slower sewing and a walking foot.
- Fibers on the right side: push the pile inward when sewing and pick fibers out after turning.
For other tools worth having, see our soft toy making supplies guide.