Animal Plush Patterns

How to make a fully articulated paper doll?

Make a fully articulated paper doll by cutting separate body segments from sturdy paper and joining them with brads, thread or paper hinges. Includes a plush-planning tip.

On this page
  1. The short answer
  2. Supplies
  3. Step-by-step
  4. Choosing a joint type
  5. Tips for smooth movement
  6. Using a paper doll to plan a plush toy
  7. Related

The short answer

To make a fully articulated paper doll, draw and cut each part of the body as a separate piece (head, torso, upper and lower arms, upper and lower legs, and hands and feet if you like) on sturdy paper, then connect the pieces at the joints with small brass brads, thread or paper hinges. Leave a small overlap at each joint so the pieces stay connected when the doll moves.

Supplies

  • Paper: Card stock, bristol board or heavy watercolor paper. Thicker paper lasts longer, but very thick card is hard to punch.
  • Cutting tools: Scissors, or a craft knife and cutting mat for fine shapes.
  • Hole-making tools: A small hole punch, a paper piercer or a needle.
  • Joint fasteners: Mini brass brads (paper fasteners), strong thread and tape, or paper strips.
  • Decorating tools: Markers, colored pencils, paint or glue for clothes and hair.

Step-by-step

  1. Sketch the doll in pieces. Draw the doll as separate segments instead of one solid figure. A common set is head, torso, two upper arms, two lower arms, two upper legs and two lower legs. Add small extension tabs, or overlap areas, at the ends of the pieces that will connect.
  2. Decorate before assembling. Color or paint the pieces first, since it is easier to work on flat parts.
  3. Cut out the pieces carefully, keeping the overlapping areas.
  4. Mark the joint points. Place the overlapping ends of two pieces on top of each other and mark where they should pivot. Choose points that are not too close to the edge, so the paper does not tear.
  5. Make the holes. Punch or pierce through both overlapping pieces at the marked point.
  6. Connect the joints. Use one of the following methods:
    • Brads: Push a mini brad through the aligned holes, and spread the prongs flat on the back.
    • Thread and tape: Thread a short piece of string through the holes, tie it or tape it on the back, and leave slight slack so the limb pivots.
    • Paper hinges: Use small paper tabs or folded strips as hinges, which keep joints flat.
  7. Test the movement. Check that each limb swings and holds its position. Loosen tight joints or tighten loose ones.
  8. Add clothing and hair without locking the joints, leaving room around fasteners.

Choosing a joint type

  • Brass brads are quick and sturdy, and give a clear pivot. They add a small bump on the back and can be tightened or loosened by adjusting the prongs.
  • Thread joints are flatter and quieter, and some makers find them easier to work with. They can fray over time.
  • Paper hinges are good for light, flat dolls, but are less durable.

Makers differ in their preferences, so you may want to try a small test joint with each type.

Tips for smooth movement

  • Leave a generous overlap around each joint, so the pieces do not pull apart when posed.
  • Use a thin spacer, such as a small paper square, between layers to reduce rubbing.
  • Do not tighten brads fully, so the limb can swing.
  • Layer the pieces so the doll looks natural. For example, put the upper arm under the shoulder of the torso.
  • For a longer-lasting doll, laminate or back the pieces with a second layer of card stock.

Using a paper doll to plan a plush toy

A paper articulated model is a handy tool for plush makers, because it shows how a body bends before you cut any fabric. You can:

  • Draw your animal or character from your sketch as separate parts and join them with brads to test the range of motion.
  • Look at where the joints should sit so the toy can sit, stand or wave.
  • Use the shapes as a starting point for a pattern; see how to design your own plushie pattern.

If you then want to build a jointed or posable plush, read making poseable stuffed animals for wire and joint options. Fabric versions of these pivots are covered in sewn joints for cloth dolls and jointing a teddy bear with cotter pins and discs.

For the full process of turning an idea into a sewn toy, see how to create your own stuffed animal.

The complete guide to animal plush patterns

Stuffed Animal Sewing Patterns: A Guide to Soft Toy Animal Patterns
Read the guide

Keep exploring

Guides from other topics

All topics →