What seam allowance is
Seam allowance is the strip of fabric between the edge of the cut piece and the stitching line. It gives the seam something to hold onto, and it’s what folds inside the toy when it’s turned right side out. If your pattern pieces show the finished outline only, with no allowance, you have to add it when cutting.
What to use
There isn’t one universal width, and the best choice depends on the pattern, the fabric and the size of the toy. Commonly used amounts:
- About 1/4 inch (6 mm): common for small toys and small pieces, where a narrow allowance keeps curves smooth and bulk low. Many plush patterns assume it.
- About 3/8 inch (1 cm) or slightly more: often used for larger toys, or for fabrics that need a bit more room.
- About 1/2 inch (1.25 cm) or more: sometimes used for fabrics that fray, stretch heavily, or are under more stress, though it adds bulk on curves.
These are typical starting points rather than rules. When in doubt, follow the pattern designer’s advice, since the pattern was drafted with a particular allowance in mind.
Check your pattern first
Read the instructions before you cut. Some patterns include the seam allowance in the pieces, and say so, while others expect you to add it. Look for a line such as “1/4 inch seam allowance included” or “add your own.” If it isn’t stated, measure the pattern against a stitching line, or sew a test piece. Using the wrong allowance can change the size and proportions of the toy.
Adding seam allowance to a pattern
If you’ve drawn your own shape, or found one without an allowance, you can add it:
- Trace the finished shape on paper.
- Draw a second line outside it at an even distance, at your chosen allowance. A ruler works for straight edges; for curves, mark dots at intervals and connect them smoothly.
- Cut along the outer line.
Alternatively, trace the shape onto the fabric and cut by eye at a consistent distance outside the line, though this is less accurate. Be careful at tight curves and points, since the outer line there is longer and may need clipping later.
Fabric and size factors
- Fabrics that fray: a wider allowance gives the seam more strength, and the edges may need extra care. Felt and fleece don’t fray, so a narrow allowance is usually fine.
- Stretchy fabrics (minky, jersey): the seam can stretch and distort. A slightly wider allowance, a stretch stitch and careful handling help. See sewing minky fabric without stretching and sewing machine features for stuffed animals.
- Long-pile fur: the pile adds bulk to the seam. Trim the fur out of the seam allowance if needed, and don’t make the allowance too narrow.
- Very small pieces: a narrow allowance makes tight curves easier to turn. See sewing tiny curved plush pieces.
- Hand sewing: a slightly wider allowance can give more room for small stitches. See hand sewing stuffed animals.
Seam allowance and final size
Each seam takes up fabric, so the finished toy is slightly smaller than the cut pieces. If the pattern’s finished shape was drafted with an allowance in mind, and you use a different one, the toy comes out larger or smaller than intended, and pieces may not fit together. Using the same allowance on every piece is important so that they line up when sewn. If you’re resizing a pattern, see how to scale a plush pattern up or down.
Trimming and clipping
After sewing, you can trim the allowance to reduce bulk, particularly on small pieces, but be careful not to cut too close to the stitches. On curves, clip or notch the allowance so it lies flat when turned. Seams that are trimmed too narrow on fabric that frays can pull apart when stuffed.
Consistency tips
- Mark the stitching line on the fabric, or use a guide on your sewing machine, such as a seam guide or a piece of tape.
- Sew a small test piece before starting on your good fabric.
- Keep the allowance the same around the whole piece, including the gap you leave for turning, so the opening can be closed neatly with a ladder stitch.
If you’re just starting out, see our beginner’s guide to making plushies for how seam allowance fits into the whole process.