Teddy Bears

Jointing a Teddy Bear with Cotter Pins and Discs

Learn how cotter pin and disc jointing works in a teddy bear: parts, tools, step-by-step assembly, getting tension right, safety notes and alternatives.

On this page
  1. What cotter pin jointing is
  2. Is it right for your bear?
  3. Tools and parts
  4. Choosing joint sizes
  5. Step-by-step: jointing a limb
  6. Jointing the head
  7. Getting the tension right
  8. Troubleshooting
  9. Alternatives

What cotter pin jointing is

Cotter pin jointing is the traditional way to attach a teddy bear’s head, arms and legs so that they swivel. Each joint is a small stack of parts: a cotter pin, one or two washers and a pair of discs, one inside the limb and one inside the body. The pin passes through the discs and the fabric of both parts, and its split ends are bent apart on the inside to lock everything in place. The limb is held snugly against the body but can still be turned.

It is the method used on many traditional and collector bears. Methods vary between makers and patterns, so use the instructions in your pattern where they differ from this general guide.

Is it right for your bear?

Cotter pin joints suit bears made from firm fabrics such as mohair, alpaca or dense faux fur, with enough size to hold the hardware. They give a satisfying, poseable feel.

They are less suitable in a few cases:

  • Toys for babies and young children. Metal pins and hard discs inside a toy can be a hazard if they come loose or the toy is damaged. Collector bears are normally sold and labeled as not suitable for small children. If the bear is for a young child, consider a no-joint design instead (see the easy stuffed bear tutorial).
  • Very soft or stretchy fabrics. The discs can pull through or distort the fabric unless it is reinforced.
  • Very small bears. There is a limit to how small the hardware can be.

Tools and parts

Parts for each joint:

  • A cotter pin
  • One or two washers
  • Two discs, commonly hardboard or plastic, with a center hole
  • Optionally, a small piece of reinforcing fabric

Tools:

  • An awl or other pointed tool for making holes
  • Needle-nose pliers, to bend and curl the pin ends
  • A sturdy thread and needle for closing seams
  • A stuffing tool or a chopstick

Joint sets are sold in packs by size. The discs, washers and pins are normally sold to match each other.

Choosing joint sizes

Larger bears need larger joints. The head usually takes the largest joint, then the legs, then the arms. A common approach is to use the biggest size that the pattern recommends for each part. Most patterns specify sizes, so follow them. If your pattern does not, a small bear of a few inches generally uses small joints, and larger bears use progressively larger ones, but check with the supplier’s size guidance rather than guessing.

Step-by-step: jointing a limb

The limb is usually jointed before it is stuffed, and before the body is stuffed. The body is left open, often along a back seam, so you can reach inside.

  1. Mark the joint position. Use the marks from the pattern on the limb and the body.
  2. Make the holes. Poke a small hole at each mark with an awl. Spread the fabric threads rather than cutting them, and keep the hole small.
  3. Assemble the limb side. Put a washer, then a disc, onto the cotter pin, with the pin’s looped head inside the limb. Then push the pin through the hole in the limb from the inside so the prongs stick out through the fabric.
  4. Stuff the limb. Stuff the limb firmly around the pin, leaving the part of the limb where the disc sits free of lumps, then close the limb opening with a ladder stitch. In some patterns the limb is stuffed first and the pin is placed later, so follow the pattern.
  5. Join to the body. Push the prongs of the pin through the hole in the body from the outside, so they come out inside the body.
  6. Add the body-side hardware. Slide a second disc and then a washer onto the prongs inside the body.
  7. Lock the pin. Use pliers to bend the two prongs apart and curl each one back outward, in opposite directions, so the hardware is held tightly. Curl them neatly, so no sharp points are left.
  8. Repeat for the other limbs. Then stuff and close the body.

Jointing the head

The head is jointed in the same way, using the hole at the base of the head and a hole in the top of the body. The neck joint is usually the largest. Many makers stuff the head and add the face before they joint it to the body, then stuff the body once all the joints are fixed. Some patterns leave the head unstuffed until the joint is attached.

Getting the tension right

Tension is a matter of feel:

  • If the limb flops or spins freely, the joint is too loose. Squeeze the prongs tighter or add a washer.
  • If the limb does not turn at all, or the fabric puckers, the joint is too tight. Loosen the curl slightly.
  • Check that the limb sits flush against the body without a gap, and that the fabric is not pulling.

Many makers test the joint before stuffing the body, so there is still access if something needs fixing.

Troubleshooting

  • Disc pulls through the fabric. Reinforce with a small patch of fabric behind the disc, or use a larger disc.
  • Joint loosens over time. Re-curl the prongs more tightly, which means reopening the body seam.
  • Sharp points. Curl the prong ends fully, so they cannot poke through the fabric.
  • Wrong side of the limb faces forward. Check the orientation of the limb against the pattern before you lock the pin, since it is hard to change afterward.

Alternatives

If you prefer a different jointing system, there are options:

  • Plastic lock joints. Two plastic discs snap onto a shaft with a lock washer. They are commonly used in toys because there are no sharp ends, but follow the manufacturer’s safety guidance.
  • Button jointing. Thread passes through the limb, body and buttons, and is pulled tight. This is lighter and sometimes used for smaller bears. Cloth dollmakers use similar methods; see sewn joints for cloth dolls.
  • No joints. Sew the limbs into the seams. This is the simplest approach, and it suits toys for small children.

For a broader view of choosing between these methods, see the teddy bear sewing pattern guide. For wire armatures and other ways to make a toy hold a pose, see making poseable stuffed animals.

The complete guide to teddy bears

Teddy Bear Sewing Pattern: How to Make a Teddy Bear
Read the guide

Keep exploring

Guides from other topics

All topics →

Cloth Doll Making for Beginners

A beginner's guide to making a cloth doll: the materials to buy, how to choose a free pattern, the basic sewing steps, and where to go for faces, hair and clothes.

Cloth Dolls 5 min read