Sock and Upcycled Toys

How to make a DIY plushie at home?

Make a DIY plushie at home: choose a simple pattern and soft fabric, add the face, sew with an opening, stuff with fibrefill and close with a ladder stitch.

On this page
  1. What you need
  2. Step 1: Choose a pattern and fabric
  3. Step 2: Cut and mark
  4. Step 3: Add the face first
  5. Step 4: Sew the pieces
  6. Step 5: Turn, stuff and close
  7. Easier routes: socks, old clothes and kits
  8. Common beginner mistakes
  9. Safety

The basic way to make a plushie at home is to choose a simple pattern and a soft fabric, cut two matching shapes, add the face, sew the pieces together with a gap, turn the shape right-side out, stuff it and close the gap with a hidden stitch. The steps below walk through each one.

What you need

  • Fabric: Fleece and felt are forgiving for beginners. Minky (a soft, plush polyester) is popular but slippery and stretchy, so it takes a bit more care; see sewing minky without stretching or shifting.
  • A simple pattern: A paper template of a basic shape such as a round animal, heart or blob. You can draw your own or use a free pattern.
  • Needle and thread, or a sewing machine
  • Fabric scissors and pins or clips
  • Fibrefill (polyester stuffing)
  • A chopstick or blunt tool for pushing stuffing into corners
  • Face materials: embroidery thread, felt, or safety eyes
  • Chalk or a washable marker for tracing

Step 1: Choose a pattern and fabric

Choose a shape with few pieces and gentle curves. A simple round body with two ears is a good first plush. Avoid thin limbs or sharp points to begin with, since they’re harder to turn out and stuff. Fabrics that don’t fray, like fleece, simplify finishing.

Step 2: Cut and mark

Trace the pattern onto the wrong side of the fabric and cut out two matching pieces, front and back. Mark where the face goes and where you plan to leave the opening, usually along a straight edge or at the bottom. If you’re using a stretch fabric, check which direction it stretches, and cut all pieces the same way for a consistent result.

Step 3: Add the face first

It’s much easier to embroider or attach features while the piece is still flat. Embroider eyes and a mouth with a few satin stitches or backstitches, or glue and stitch on felt shapes. Hold the pieces up and check the face placement before you stitch it down. If you’re using safety eyes, follow the manufacturer’s instructions for fitting (how to attach safety eyes), since they are normally fixed before stuffing.

Step 4: Sew the pieces

  1. Place the two pieces with right sides together, pinning or clipping the edges.
  2. Sew around the edge with a small seam allowance, commonly around 1/4 to 3/8 inch (about 6-10 mm), using a running stitch, backstitch or a sewing machine.
  3. Leave a gap of a few centimetres in the seam, so you can turn the toy out and stuff it.
  4. Backstitch at the beginning and end of the seam to secure it.
  5. Clip small notches in the seam allowance around curves and trim any corners, being careful not to cut the stitching.

Step 5: Turn, stuff and close

  1. Turn the toy right-side out through the gap, using a blunt tool to push out corners.
  2. Stuff in small pieces, starting with the extremities and working toward the middle. Aim for firm enough to hold the shape but not so tight that the seams strain.
  3. Fold the edges of the gap inward and close it with a ladder stitch. This is a hidden stitch that goes back and forth between the two folded edges, then pulls tight to close the gap invisibly.
  4. Knot the thread, then pass the needle through the toy and snip it so the end disappears inside.

Easier routes: socks, old clothes and kits

If sewing from a pattern feels like a lot, there are gentler starting points:

Common beginner mistakes

  • Choosing a pattern with too many small pieces
  • Stuffing in big clumps, which makes the toy lumpy (see how to stuff a plushie evenly)
  • Forgetting to leave a gap for turning
  • Sewing the face on after closing, when it’s much harder to do neatly
  • Overfilling so that seams pull open

Safety

For babies and toddlers, avoid buttons and plastic eyes, which can come loose, and embroider the features instead (making a baby-safe stuffed animal). Use new stuffing intended for toys, and check that all seams are firm before giving the toy to a child. If you’re sewing a toy for a child, you may also want to look at toy safety guidance that applies where you live.

The complete guide to sock and upcycled toys

Making Soft Toys from Old Socks
Read the guide

Keep exploring

Guides from other topics

All topics →